Sloan Crown & Crown II Flushometer - Repair Parts Breakdown

Sloan Bedpan Washer Repair Parts Breakdown

PARTS LIST
1	# 08725	1-1/2" x 21-1/2" CP VACUUM BREAKER
	# 80795	1-1/2" x 13-1/2" CP VACUUM BREAKER (ADA HEIGHT)
	# 08436	1-1/2" x 21-1/2" CP VACUUM BREAKER WITH 2" OFFSET
2	# 08438	VACUUM BREAKER REPAIR KIT
3	# 08812	1-1/2" SLIP JOINT COUPLING
4	# 08329	DIVERTER VALVE BODY (NON-Deoseptic Bottle)
4	# 80820	DIVERTER VALVE BODY (Deoseptic Bottle)
5	# 08813	WALL SUPPORT KIT
6	# 08528	OUTLET TUBE GASKET
7A	# 80821	OUTLET TUBE
7B	# 08073	OUTLET TUBE WITH 1-1/2" OFFSET
8	# 80822	1-1/2" COUPLING NUT
9	# 08017	1-1/2" SPUD COUPLING ASSEMBLY
10	# 08093	SPRAY ARM REPLACEMENT KIT
10	# 08846	SHORT SPRAY ARM REPLACEMENT KIT (for use with F-182 Offset Outlet Tube)
11	# 08846	SPRAY ARM REPAIR KIT
12	# 08803	PIVOT REPLACEMENT KIT
	-	DIVERTER VALVE ASSEMBLY & SPRAY ARM ASSEMBLY

DEOSEPTIC UNIT PARTS
13	# 08802	DEOSEPTIC
13A	# 08354	O-RING PISTON - 2 REQUIRED
13B	# 08355	SET SCREW
13C	# 08361	DIVERTER VALVE SEAL WASHER
13D	# 08360	DIVERTER VALVE SEAL
14	# 80823	PLUG BUTTON
15	# 80824	SWIVEL & BALL CHECK ASSEMBLY
16	# 80825	ASPIRATOR TUBE ASSEMBLY
16B	-	LOCKING RING
17	# 80826	DEOSEPTIC SOLUTION BOTTLE
To place an order, call us toll free at 1-800-442-6622



TROUBLESHOOTING GUIDE FOR SLOAN SLIMLINE BEDPAN WASHER FLUSHOMETERS


1	PROBLEM:
	DIVERTER LEAKING AT SPRAY ARM

	CAUSE:
	A) Diverter spray arm (old style) is damaged.
	B) Spray arm o-ring is damaged or installed improperly.

	SOLUTION:
	A) Replace diverter arm with new spray arm replacement kit # 08093. NOTE: On old style diverter spray arm, the spray arm o-ring was placed on groove at the end of the spray arm. When installing new spray arm kit, place washer into bottom of hole of nozzle pivot. Then place the o-ring on top of washer. Insert new spray arm into the pivot, pressing in slightly. While holding spray arm in place, tighten set screw.
	B) Re-Install o-ring as described above in step (A.) If leakage persists, replace using spray arm kit # 08093


2	PROBLEM:
	DIVERTER LEAKING AT NOZZLE PIVOT.

	CAUSE:
	A) One or both pivot o-rings are worn.
	B) Diverter seal washer worn or missing.
	C) Nozzle pivot damaged or defective.

	SOLUTION:
	A) Replace nozzle pivot assembly.
	B) Replace pivot seals. Use diverter rebuild kit.
	C) Replace nozzle pivot assembly. Use pivot replacement kit.


3	PROBLEM:
	ERRATIC SPRAY PATTERN FROM SPRAY ARM NOZZLE

	CAUSE:
	A) Debris clogging nozzle screen.
	B) Damaged or missing nozzle screen or spray disc.

	SOLUTION:
	A) Wash nozzle screen under running water.
	B) Replace using # 08846 spray arm repair kit.


4	PROBLEM:
	DEOSEPTIC SOLUTION NOT SIPHONING FROM BOTTLE DURING FLUSH CYCLE (Deoseptic models only.)

	CAUSE:
	A) Adjusting screw not open.
	B) Aspirator tube screen clogged.
	C) Aspirator tube not installed completely onto swivel & ball check assembly.
	D) Aspirator tube cracked.
	E) Rubber ball check stuck inside swivel & ball check assembly.

	SOLUTION:
	A) Open adjusting screw until adequate amount of solution is siphoned from bottle during flush cycle.
	B) Remove solution bottle. Remove aspirator tube from swivel & ball check assembly and wash screen under running water.
	C) Remove solution bottle. Make sure aspirator tube is pushed completely onto nipple of swivel & ball check assembly.
	D) Replace aspirator tube assembly.
	E) Remove solution bottle and aspirator tube from swivel & ball check assembly. Gently insert small implement (paper clip, small dia. hex key, etc.) into nipple of swivel & ball check assembly to dislodge rubber ball check.




5	PROBLEM:
	WATER LEAKING BACK INTO SOLUTION BOTTLE

	CAUSE:
	A) Rubber ball damaged or missing.
	B) Rubber ball not sitting in seat of swivel & ball check assembly.

	SOLUTION:
	A) Replace rubber ball using Deoseptic Diverter Rebuild Kit. Includes Outlet Tube Gasket (item 6,) Spray Arm Repair Kit (item 11,) and all items in Pivot Replacement Kit (item 12) except Pivot.
	B) Remove swivel and ball check assembly, taking care not to lose rubber ball. Insert rubber ball back into seat of swivel & ball check assembly and reassemble. NOTE: Follow steps in solution (E) of problem 4.

Equiparts • 1003 Main St. • Pittsburgh, PA 15215

Pittsburgh: 412-781-9100 • Toll Free: 800-442-6622 • Fax: 412-781-3085

© 2010 Equiparts Corp. All Rights Reserved.