SLOAN ELECTRONIC FAUCET REPAIR PARTS BREAKDOWN
 
EBF-550
Sloan EBF-550 faucet repair parts
1A
# 80762
Faucet and Sensor Assembly - with Standard Gooseneck Spout
1B
# 80763
Faucet and Sensor Assembly with Surgical Bend Gooseneck Spout
2
# 80751
Adapter for Spray Heads (not required for AC-55-a Shower Spray Head)
3A
# 59462
0.5 gpm Spray Head with Key (female thread)
# 55670
2.2 Aerator Spray Head with Key (female thread)
# 54677
2.2 Laminar Flow Spray Head (female thread)
# 54693
 Replacement Key ONLY for ETF-1021-A 0.5 gpm Spray Head and ETF-1022-A 2.2 gpm Aerator Spray Head (NOT required for ETF-237 2.2 gpm Laminar Flow Spray Head) 
3B
# 80750
Shower Spray Head Assembly 2.2 gpm
4
# 80765
Faucet Mounting Kit includes Base Gasket, large Flat Washer, large Lock Washer, large Nut, Mounting Spacer, Mounting Stud, small Flat Washer, small Lock Washer, small Nut, Anti-Rotation Screw, and ETF-591 Compression Fitting Connector (male)
# 80764
1/8" NPT Pipe to 3/8" Tube Male Compression Fitting Connector
5A
# 80753
Single Solenoid Supply Kit includes two Compression Nuts two Compression Sleeves and Screwdriver
5B
# 54682
3/8" Tee Compression Fitting
6
# 54325
Control Module Assembly includes Base Enclosure, Cover Enclosure, two Gaskets, Solenoid Body, Solenoid Enclosure, Solenoid Filter Cap, and Battery Stop
7
# 54686
Mounting Hardware Kit for Control Module Assembly includes four Anchor Nuts, four Toggle Nuts, four Mounting Screws for Base Plate, four Flat Washers, four Anchors, and four Metal Screws.
8
# 08218
Back Check
9
# 80766
Old Faucet Mounting Kit includes 3/8" Water Supply Tube, Base Gasket, large Flat Washer, large Lock washer, large Nut, and ETF-547 Compression Fitting Connector.
10
# 54685
1/8" NPT Pipe to 3/8" Tube Female Compression Fitting Connector
 
# 80767
Sensor Housing and Cable Assembly Replacement Kit
 
# 80754
Solenoid Replacement Kit includes Solenoid Body, Solenoid Enclosure, and Solenoid Filter Cap
 
# 08578
Solenoid Filter Replacement Kit includes Filter Screen Assembly and O-Ring
# 80756
Repair Kit for EBF-60 Control Module Assembly includes EBF-61-A Battery Holder Assembly and EBF-159 Battery Gasket Control Module Replacement Gaskets.
MAINTENANCE GUIDE FOR THE EBF-550 FAUCET
1
PROBLEM:
Sensor troubleshooting LED does not function (red indicator light does not flash during set-up procedure.)
CAUSE:
A) No battery power is being supplied to Sensor
B) Insufficient battery power is being supplied to Sensor
C) Sensor Cable is not properly inserted
D) Sensor Range is set at minimum distance
E) Control Module assembly is defective
SOLUTIONS:
A) Ensure that the batteries are installed properly. Check that the orientation of each battery matches the positive and negative symbols shown on the bottom of the battery compartment. Reinsert the Battery Compartment into the Control Module.

B) One or more of the batteries is "dead." To ensure proper operation, replace with four new C-size batteries
( order four # 32739 batteries from Equiparts by calling 800-442-6622.) Check that the orientation of each battery matches the positive and negative symbols shown on the bottom of the battery compartment. Reinsert the Battery Compartment into the Control Module.

C) Disconnect and reconnect Sensor Cable to the Control Module.
D) Increase Sensor range. Use a small phillips screwdriver to turn the potentiometer screw (white screw in a blue base) clockwise.
E) Replace EBF-60-A Control Module assembly by ordering part # 54325 from Equiparts. Call 800-442-6622 to order.
2
 PROBLEM:
Faucet does not deliver any water when Sensor is activated.
INDICATOR:
A) Solenoid valve produces an audible "click."
CAUSE:
A) Water supply valve is closed
SOLUTION:
A) Open the supply stop.
INDICATOR:
B) Solenoid valve does NOT produce an audible "click."
CAUSE:
B) Solenoid lead is not properly connected to the Control Module
SOLUTION:
B) Disconnect and reconnect Solenoid lead to the Control Module
CAUSE:
C) Batteries are not installed properly.
SOLUTION:
C) Check that the orientation of each battery matches the positive and negative symbols shown on the bottom of the battery compartment. Reinsert the battery compartment into the control module. The troubleshooting LED should flash red when a user is detected
CAUSE:
D) Solenoid needs replaced
SOLUTION:
D) Order part # 54335 from Equiparts. To order, call 800-442-6622.

3
 PROBLEM:
Faucet delivers only a slow flow or dribble when sensor is activated.
CAUSES:
A) Water supply valve is partially closed.
B) Solenoid Filter is clogged.
C) Aerator or Spray Head is clogged.
D) Aerator needs replaced.
SOLUTIONS:
A) Completely open the Supply Stop.
B) Remove, clean, and reinsert. Replace (EBF-1004-A) Solenoid Filter Kit if necessary by ordering part # 08578 from Equiparts. Call 800-442-6622 to order.
C) Remove, clean, and reinsert.
D) Call Equiparts at 800-442-6622 to order part # 59857.
4
 PROBLEM:
Faucet does not stop delivering water or continues to drip after user is no longer detected (automatic shut-off fails even when batteries are removed.)
CAUSE:
A) Solenoid Valve has been connected backwards.
  B) Solenoid Valve is dirty.
  C) Solenoid Valve Module is defective.
 
SOLUTIONS:
A) Disassemble Solenoid Valve compression fittings at the inlet and outlet positions. Water should flow from inlet through the Solenoid Valve to outlet according to the direction shown by the arrow on the side of the Solenoid Valve. Reconnect the compression fittings in the correct orientation.
B) Back flush by reversing water flow (opposite to the direction shown by the arrow on the side of the Solenoid Valve) through the Solenoid Valve. Reconnect the compression fittings in the correct orientation. Activate faucet.
C) Replace (EBF-62-A) Solenoid Valve Module by ordering part # 80754 from Equiparts. Call 800-442-6622 to order.
5
 PROBLEM:
The water temperature is too hot or too cold on a faucet connected to hot and cold supply lines with two Back Checks.
CAUSES:
A) Supply Stops are not adjusted properly.
B) One Back Check is installed backwards.
SOLUTIONS:
A) Adjust Supply Stops
B) Reinstall Back Check
NOTE: For some systems, a thermostatic mixing valve may be required. Order part # 54621 from Equiparts. Call 800-442-6622 to order.
Equiparts  •   1003 Main St.  •  Pittsburgh, PA 15215
Pittsburgh: 412-781-9100   •  Toll Free: 800-442-6622   •   Fax: 412-781-3085
© 2008 Equiparts Corp. All Rights Reserved.